Integrated Cart: $875

The sleek design blends the cart with a VersaLaser™ laser engraver for a stylish floor standing unit.

• Maximum stability at low cost

• Durable construction for many years of dependable service

• Locking casters for moving convenience

• Two large storage drawers

• Top indents "lock" VersaLaser™ unit in place

Size:
25" W x 22" D x 30" H
(635mm x 559mm x 762mm)

Weight:
95 lbs. (43.1 kg)

 Computer Controlled Air Cleaner / Cart: $2715

The same sleek design and function as the Integrated Cart except storage space is replaced by built in air cleaner for your VersaLaser laser engraver.

• Controlled through a USB port and activated only when jobs are in process

• Air cleaner is concealed behind drawers (no storage)

• Air filtration eliminates smoke and dust

• Top indentations "lock" VersaLaser unit in place

Size:
25"W x 27"D x 30"H
(635mm x 686mm x 762mm)

Weight:
160 lbs. (72.6 kg) without filters (shipped with one set of filters); 170 lbs. (77 kg) with filters installed

Recommended for installations where venting to the outside is not convenient or possible.

 Replacement Filters:

Replacement filters for your VersaLaser laser engraver.

Pre-filter: $18

• Captures dust and large particles

HEPA Filter: $150

• Captures smoke

Carbon Filter: $390

• Removes odor

 Cylindrical Object Rotary Accessory: (VL-2.30 - $850, VL-3.50 - $900)

Allows a VersaLaser™ laser engraver to be quickly reconfigured to engrave and cut cylindrical objects.

• Allows maximum part diameter of up to 5.0 inches (127mm)

• Loading and unloading is quick and easy

• An easy to use software interface provides for quick and precise layout on any material

• Hot swappable for convenience

• A sensor detects the presence of rotary fixture when it's installed and adjusts automatically

For VL-2.30

Size:
18.8" W x 4.8" D x 5.3" H
(478mm x 122mm x 135mm)
Weight:
9 lbs. (4.1 kg)

For VL-3.50

Size:
26.8” W x 4.8” D x 5.3” H
(681mm x 122mm x 135mm)
Weight:
10 lbs. (4.5kg)

 Vector Cutting Accessory: (VL-2.30 - $240, VL-3.50 - $340)

A simple yet functional design provides support and light vacuum hold down for sheet stock while allowing smoke and debris from the cutting process to be removed from your VersaLaser laser engraver.

• Honeycomb cutting surface supports material with a minimum of contact area

• Hot swappable for convenience

• A sensor detects the presence of cutting table when it's installed and automatically adjusts the Z-axis automatically to place materials at the proper focus

Recommended for cutting thin materials that tend to curl or cutting materials where visual cut quality is important on both front and back of cut material.

For VL-2.30

Size:
18.8" W x 14.5" D x 4.5" H
(478mm x 368mm x 114mm)
Weight:
3 lbs. (1.4 kg)

For VL-3.50

Size:
26.8” W x 14.5” D x 4.5” H
(681mm x 368mm x 114mm)
Weight:
4 lbs. (1.8kg)

 Super Resolution Accessory: $2,650

Allows engraving of smaller text, higher resolution graphics and photographs and vector marking and cutting of thinner lines for your VersaLaser laser engraver.

• Engrave smaller text

• Vector mark and cut thinner lines

• Mark uncoated metals, like stainless steel, without using metal marking compounds

 Computer Controlled Compressed Air Unit: $1,290

Supplies dry oil-free compressed air to protect optics and enable air assisted cutting and engraving for your VersaLaser laser engraver.

• Controlled through a USB port and is activated only when jobs are in process

• The compressor pump is noise insulated for quiet operation

• An air dryer is integrated into the unit to remove optics damaging water

Size:
14.2"W x 11.1"D x 18"H
(361mm x 282mm x 457mm)

Weight:
44 lbs. (20 Kg)

Recommended for any cutting operation or engraving operation that creates dust or smoke to protect optics.

Must purchase Refrigerated Dryer Kit ($1,290) or Desiccant Dryer Kit ($430) separately

 Air Assist Back Sweep: $225

Recommended for use with the Computer Controlled Compressed Air Unit, the Back Sweep attachment directs air toward the exhaust duct  of your VersaLaser laser engraver. This is important for rubber engraving or engraving of other materials that produce a lot of dust during the engraving process.

 Air Assist Cone: $140

Recommended for use with the Computer Controlled Compressed Air Unit, the cone directs air onto material being cut or engraved and improves cutting or engraving quality of most materials used in your VersaLaser laser engraver.

 Lens Kit: (1.5” 2.0") $328

(2.0" lens included with each VersaLaser laser engraver)

• Introductory Kit $595

• Standard Kit $1,595

• Expanded Kit $2,985

ORDER MATERIALS:

(Click Here)

 

**SPECIAL OFFERS**

(Click Here)